日韩欧美一二三,人妻一区二区高清免费,欧美 亚洲 日韩精品 一区,亚洲第一三级片网站

Welcome [Wuxi Yi Jin Machinery Co. Ltd.] official website!
Chinese   |   English   |  Sitemap
News

Position:Home > News >

Centrifugal fan installation

Centrifugal fan in the end is how to install, centrifugal fan manufacturers of workers is described as follows:
1.Centrifugal fan of the overall unit installation, should be placed directly on the basis of pairs of oblique horn leveling.
2.On-site assembly of the centrifugal fan, the base of the cutting surface should be properly protected, there should be no corrosion or operation, the base placed on the basis of the application of pairs of oblique horn leveling.
3.The bearing seat and the base should be tightly engaged, the vertical non-level should not exceed 0.2 / 1000, with the level on the spindle measurement, horizontal horizontal water should not exceed 0.3 / 1000, with the level of the bearing in the level of the sub-surface measuring.
4.Before the bearing grinding, the rotor axis should be corrected with the axis of the chassis, and the gap between the impeller and the inlet and the clearance between the spindle and the rear side of the housing should be adjusted to match the equipment technology The provisions of the document.
5.When the spindle and the bearing are assembled, they should be inspected according to the equipment technical documents. Bearing bearing and bearing pad should be maintained between 0.03-0.04 mm interference.
6.When the fan housing is assembled, the position of the housing should be determined on the basis of the rotor axis and the axial and radial clearance between the inlet of the impeller and the air inlet of the cabinet should be high and within the specified range. Whether the anchor bolts are fastened. If the gap is not specified in the technical documentation, the general axial clearance shall be 1/100 of the outer diameter of the impeller. The radial clearance shall be evenly distributed. The value shall be 1.5 / 1000-3 / 1000 of the outer diameter of the impeller. Adjust the value of the gap to try to improve the efficiency of the fan.
7.When the fan is correct, the fan shaft and the motor shaft of different degrees of axis: radial displacement should not exceed 0.05 mm, the tilt should not exceed 0.2 / 1000.
8.Rolling bearing assembly of the centrifugal fan, the two bearing frame on the bearing hole of different shaft degrees, until the rotor is installed, to flexible rotation prevail.

Contact: Mr. Wei 180 6833 7327 / 133 9518 5578 7 ????Tel: 0510-83303276 ????Fax: 0510-83303276

E-mail: 2637472470@qq.com ????Web: oulnd.cn ????Add: Luoxian Town, Huishan District, Wuxi City

Copy right ? 2017 Wuxi Yi Jin Machinery Co., Ltd. All Rights Reserved

中文字幕日韩无码欧美| 国产1区9999| 亚洲一色天堂| 国产日韩欧美在线不卡视频| 啪啪啪国产综合网| 成人副利AV在线| 亚洲日韩高清1区二区三区| 丁香五月无毒不卡激情在线| 中国女人操逼大全| 偷偷要色偷偷婷婷| 一男两女黄色插B网站| 日韩午夜欧美精品一二三四| 亚洲欧美日韩BT淫| 曰韩精品无码一区二区三区| 亚洲男人天堂电影在线| 欧美 不卡 久久| 日韩 欧美 3p| 艹骚屄在线中出在线中出在线中出| 亚洲手机AV网址大全| 欧美日韩996| 97x视频| 日韩精品 欧美 中文| 偷拍久久福利视频 | 综合亚洲二区人一区| 欧美黄片网战| 丁香五月婷婷狼牙视频| 成人小说av| 国产一区二区黑人欧美| 逼在线观看网站| 午夜欧美专区| 国产激情午夜| 亚无午夜福利视频91| 91,色情热久久| 成人免费午夜福利无码AV | 天天干天天曰屄| 艹穴视频在线观看| 观看免费干B| 精品熟妇av免费网站| 国产精品亚洲精品| 亚洲日韩精品av中文无码| 麻豆av无码一区二区三区四区|